The Right Framework for This Decision
Most "single router vs mesh" guides compare product specs and end with "it depends." I want to give you something more useful: the actual square footage and layout conditions where each option makes sense, backed by DCSpeedTest data from multiple configurations.
The two products I compared: the GL.iNet Flint 2 ($170) as the single router, and the NETGEAR Orbi RBK752 ($479) as the mesh system.
Test Results by Square Footage and Layout
Scenario A: 800 sq ft Apartment, Open Plan
| Location | GL.iNet Flint 2 | Orbi RBK752 |
|---|---|---|
| Living area (10 ft) | 742 Mbps | 680 Mbps |
| Bedroom (30 ft) | 534 Mbps | 512 Mbps |
| Far corner (50 ft, 1 wall) | 381 Mbps | 412 Mbps |
Winner: GL.iNet Flint 2 (single router) — Coverage is complete, performance is slightly better at shorter distances, and you save $309. For a small apartment, a single good router is all you need.
Scenario B: 1,600 sq ft Single-Story, Standard Construction
| Location | GL.iNet Flint 2 | Orbi RBK752 |
|---|---|---|
| Near router (10 ft) | 742 Mbps | 680 Mbps |
| Mid-home (40 ft) | 389 Mbps | 451 Mbps |
| Far end (70 ft, 2 walls) | 198 Mbps | 389 Mbps |
Winner: depends on tolerance. At 70 feet, the Flint 2 delivers 198 Mbps — usable for anything practical. The Orbi delivers 389 Mbps. If 198 Mbps at the far end is acceptable, the Flint 2 saves $309. If you want strong coverage everywhere with headroom, the Orbi is better.
Scenario C: 2,800 sq ft Two-Story, Mixed Construction
| Location | GL.iNet Flint 2 | Orbi RBK752 |
|---|---|---|
| Ground floor near router (15 ft) | 698 Mbps | 641 Mbps |
| 2nd floor, mid (50 ft + floor) | 289 Mbps | 498 Mbps |
| 2nd floor, far end (80 ft + floor) | 141 Mbps | 421 Mbps |
Winner: Orbi RBK752 mesh system — The 3x performance difference at 80 feet through a floor is too significant to ignore. The single router's 141 Mbps is functional but represents a noticeable quality-of-experience gap vs the Orbi's 421 Mbps. For a home this size, the mesh system is the right tool.
The Decision Line: Around 2,000 sq ft
Based on my testing: a single high-quality WiFi 6 router like the GL.iNet Flint 2 covers homes up to approximately 1,800–2,000 sq ft (single story, standard construction) with acceptable performance throughout. Above that, or with any of these complicating factors, the mesh system becomes worthwhile:
- Multiple floors (each floor transition costs significant signal strength)
- Dense wall construction (brick, concrete, plaster absorb signal more than drywall)
- L-shaped or non-linear floor plan where "centrally placed" still leaves corners far from any one router position
- Consistent need for strong signal at the far end of the home (gaming, video calls, 4K streaming)
The Cost Question
The Flint 2 is $170. The Orbi is $479. That's a $309 difference. For a home under 1,600 sq ft with acceptable far-corner performance from the Flint 2, the $309 savings is real money you don't need to spend. For a 2,800 sq ft home where the Orbi's performance advantage is significant and daily, the $309 is the cost of a genuinely better experience over several years of use. Context determines whether it's worth it.
FAQ
Can I add a second GL.iNet Flint 2 to cover a large home?
Yes — running a second Flint 2 as an access point (connected via ethernet to the primary) gives you two-node coverage without a mesh system. This approach works well and costs $340 for two Flint 2 units vs $479 for the Orbi. The tradeoff: you need an ethernet cable run between the two units for best performance, and the seamless roaming between nodes isn't as polished as the Orbi's dedicated mesh protocol.
What if my home is exactly at the borderline — around 2,000 sq ft?
At the borderline, start with the Flint 2 single router. Run DCSpeedTest from every room after installation. If all rooms show usable speeds (100+ Mbps) and you don't have specific rooms with inadequate coverage, you're done. If one area is still weak, add a Finwarm extender to that specific area for $72 before considering the full mesh upgrade at $479.